Talk:CF Standard Names - Discussed Atmospheric Chemistry and Aerosol Terms
Go back to Start page for Atmospheric Chemistry and Aerosol Names PLEASE DO NOT USE THE NAVIGATION BAR ON THE LEFT HAND SIDE!
Important issues are marked in RED , please COMMENT!
NOy[edit source | reply | new]
Vincent-Henri PEUCH VHP - CT - Jonathan Gregory JG - Frank Dentener FD
- there is always the problem that "NOy" has no fully agreed definition in the literature... It is perhaps unwise to use it in the name? Could we use "total_nitrogen_oxides" instead?
- (JG))I think it's a good idea to avoid the word "total" if we can, as it is not always obvious what aspect is being totalled! total_nitrogen_oxides is probably clear enough, but maybe all_nitrogen_oxides might be better?
- (CT) But what does 'all' include? anyway, I changed it.
- (FD) NOy it is a matter of defining accurately. Total Nitrogen is a very confusing term, in biological applications it may mean something completely different. NOy=NO+NO2+HNO3+NO3aerosol+2 N2O5 + NO3(radical) + HNO4 + PAN + other organic nitrates.
- (CT) some models might not have all these species, I define it now as:
- standard_name: atmosphere_mole_fraction_of_all_nitrogen_oxides
- explanation: volume mixing ratio of nitrogen oxides NOy, i.e., sum of moles_fractions of all simulated oxidized nitrogen species, (NO, NO2, HNO3, NO3aerosol, N2O5, NO3(radical), HNO4, PAN, other organic nitrates) (N2O5 is only counted once!)
- (CT) Another difficulty arises from N2O5, that contains to N atmos. Frank wrote 2*N2O5 in his definition, but if we count in mole or kg - not kgN!, this is not correct. Therefore, I have added (N2O5 is only counted once!)
Tropopause definition[edit source | reply | new]
Christiane Textor CT - Jonathan Gregory JG - Vincent-Henri Peuch VHP
- CT: Several tropopause definitions exist:
- - chemical tropopause (150 ppb O3 isosurface)
- - lapse rate tropopause (the lowest level at which the lapse rate decreases to 2 °C/km or less,
- provided that the average lapse rate between this level and all higher levels within 2 km does not exceed 2 °C/km. WMO definition of Tropopause)
- - potential vorticity (PVU2 (at the 2 PVU surface) or PVU1.5 (at the 1.5 PVU surface))
- - potential temperature surface
- JG: tropopause_defined_by_...
- If you need to distinguish different definitions of the tropopause, this could be done by defining different standard names. This issue is rather like the definition of the ocean mixed layer, for which we have several standard names:
- If there are particular numbers which are needed for the definition (like your 150 ppb O3) they could be specified as standard name parameters (but we still haven't agreed the mechanism for this!).
- CT: This would then give X_mole_content_in_air_below_tropopause_defined_by_150ppv_O3_iso_surface.
- JG: For X_mole_content_in_air_below_tropopause_defined_by_150ppv_O3_iso_surface: I was thinking it is better avoid putting "parameter" like 150 ppb in the name. When it is necessary to record such parameters to define a standard name, we should use some other attribute. This has come up before and I refer to them as "standard name parameters" but we have not decided how it should be done! For instance, it could be a new attribute, or it could be a scalar coordinate variable. This needs to be debated. I think a generic name such as X_mole_content_in_air_below_tropopause_defined_by_ozone_mole_fraction would be all right, and we could mention the 150 ppb in the definition (for the moment).
- CT: X_mole_content_in_air_below_tropopause_defined_by_ozone_mole_fraction is the new name so far, but the tropopause definition is still not agreed on, it could be:
- VHP: troposphere_content
- The description of the "troposphere_content*" variables is not enough detailed because it is indeed verticaly integrated, but up to the tropopause only. We can specify in the explanation "up to the tropopause level", but we probably also have to specify the tropopause definition to be used (2PVU,380K ?) as the value is quite sensitive to the specific criterion used (for species with strong vertical gradients at the tropopause like ozone). A drawback of specifying is that any other type of hypotheses (other "tropopause" definition : 150 ppb of ozone, 100 hPa,...) or other ways of computation (specific tracer in the model) would then no longer fit with the name. I don't know the solution...
- CT: The 150ppb O3 isosurface is a good measure for atmospheric chemsitry problems and has been used in ACCENT/PHOTOCOMP. Changed to up_to_chemical_tropopause_content as in e.g. "up_to_chemical_tropopause_content_of_ozone_in_air".
- VHP: mole_fraction_of_ozone_from_stratosphere_in troposphere
- The variable "mole_fraction_of_ozone_from_stratosphere_in troposphere" is a modeler's concept, with no chance of being measured. The way it is implemented in a model has an impact on the actual values, due to non linearities etc... I would not be in favor of including it as a standard variable. What do you think?
- JG "The variable mole_fraction_of_ozone_from_stratosphere_in troposphere is a modeler's concept." Yes, that is true, but if modellers want to store this quantity, and compare it among models, then it should be given a standard name. There are many quantities like this, which aren't really observable. To begin with CF was designed for models, rather than the real world!
Construction of deposition flux names[edit source | reply | new]
Jonathan Gregory - Christiane Textor (CT)
- I would suggest that due_to_turbulence comes after of_X, because there could be a quantity dry_deposition_flux_of_X, of which dry_deposition_flux_of_X_due_to_turbulence is a part.
- (CT) It is :dry_deposition_mole_flux_of_X=dry_deposition_mole_flux_of_X_due_to_turbulence+dry_deposition_mole_flux_of_X_due_to_sedimentation, so I would rather like to leave the due_to_turbulence and due_to_sedimentation close to deposition, so I would like to change it to dry_deposition_mole_flux_of_X=dry_deposition_due_to_turbulence_mole_flux_of_X+dry_deposition_due_to_sedimentation_mole_flux_of_X, ok?
Grid box area[edit source | reply | new]
Jonathan Gregory - Christiane Textor (CT)
- Do you have a data variable containing area? If the only purpose of this is to provide weights, you can use cell_measures to supply the area variable (CF 7.2). However if you do have them as data variables, I agree you need a standard name. I'd suggest surface_area. I think this is really the quantity, isn't it. It is analogous to sea_ice_area (m2), for example. These are extensive quantities in space; they implicitly depend on the size of the grid box.
- (CT) I reread the CF documentation yesterday and realized the possibility of using the cell methods for the grid information, sorry for that. We do not need an additional standard_name.